Ideal
Logic Max Combi C30
Combi Boiler
30kW
2019-present
ErP A
77 fault codes
<p>The Logic Max Combi C30 is a combi boiler from Ideal, available at 30kW output. Produced 2019-present.</p>
Logic Max Combi C30 Fault Codes 77
Code
Description
Severity
Type
C0
Fan Fault — Fan Not Running
The fan has failed to start or is not reaching operating speed. C0 is a lockout…
High
Engineer
View Guide
C0 0
Fan Not Running at Start (Sub-code)
The fan is not running at the point in the start sequence where it is required.
High
Engineer
View Guide
C1
Flue Temperature Too High
The flue gas temperature has exceeded the safe limit. The boiler has shut down to prevent…
High
Engineer
View Guide
C2
Fan Fault — Speed Out of Range
The fan speed is outside the expected operating range — either too slow or too fast.
High
Engineer
View Guide
C3
Air Pressure Switch Open
The air pressure switch is not closing when the fan runs. The boiler cannot confirm adequate…
High
Engineer
View Guide
C5
Rapid Temperature Rise
Flow temperature rising too quickly, indicating poor circulation.
High
Engineer
View Guide
C6
Flow/Return Differential Too Large
The temperature gap between flow and return is abnormal.
Medium
Engineer
View Guide
F1
Low Water Pressure
The boiler's water pressure has dropped below the minimum operating level. One of the most common…
Low
DIY
View Guide
F10
DHW Temperature Sensor Fault
The domestic hot water temperature sensor has a fault. On combi boilers, this prevents safe hot…
Medium
Engineer
View Guide
F11
Cylinder Sensor Fault
The hot water cylinder temperature sensor has a fault. Relevant on system boilers paired with a…
Medium
Engineer
View Guide
F12
Flame Loss During Operation
The boiler had a stable flame but lost it during operation. This can be caused by…
High
Engineer
View Guide
F13
Gas Pressure Sensor Fault
The gas pressure sensor is giving an out-of-range reading, preventing safe operation.
High
Engineer
View Guide
F14
Gas Valve Fault
The gas valve is not responding correctly to commands from the PCB.
High
Engineer
View Guide
F15
PCB Communication Fault
The printed circuit board (PCB) has an internal communication error. Key boiler components cannot communicate correctly.
High
Engineer
View Guide
F16
Fan Fault
The fan is not running at the correct speed or has stopped. The boiler cannot safely…
High
Engineer
View Guide
F17
Pump Over-Run Fault
The pump did not stop after the burner shut down.
Medium
Engineer
View Guide
F2
Flame Loss
The boiler has lost its flame during operation or failed to ignite.
Medium
DIY
View Guide
F20
Pressure Sensor Fault
The electronic water pressure sensor is giving incorrect readings.
Medium
Engineer
View Guide
F3
Fan Fault
The boiler fan is not operating at the required speed, preventing safe ignition.
High
Engineer
View Guide
F4
Flow Thermistor Fault
The flow temperature sensor (thermistor) is giving an incorrect reading or has failed.
Medium
Engineer
View Guide
F5
Return Thermistor Fault
The return temperature sensor is giving an incorrect reading or has failed.
Medium
Engineer
View Guide
F6
Outside Sensor Fault
The external temperature sensor (used for weather compensation) is faulty or not connected. This does not…
Low
Engineer
View Guide
F7
Low Mains Voltage
The mains voltage supply to the boiler has dropped below the safe minimum (185V).
Medium
Engineer
View Guide
F8
Flow Thermistor - Out of Range High
The flow temperature sensor is reading higher than its maximum expected value, indicating a sensor fault…
High
Engineer
View Guide
F9
Unconfigured PCB
The Printed Circuit Board has not been configured correctly. This almost always occurs after a PCB…
Medium
Engineer
View Guide
FA
Flow/Return Sensors Reversed (Regular Boilers)
On Ideal Logic Max and Logic Plus regular (heat-only) boilers, code FA indicates the flow and…
Medium
Engineer
View Guide
FD
Condensate Blocked / Frozen
The condensate drain system is blocked or frozen. FD is Ideal's code for a blocked condensate…
Medium
DIY
View Guide
FN
Flame Loss (Alternative Code)
On some Ideal models, FN is displayed alongside or instead of F2 to indicate flame loss…
Medium
DIY
View Guide
FU
Temperature Difference Too High — Check Isolation Valves
The temperature difference between the flow and return is greater than 50°C. The boiler is blocking…
Medium
DIY
View Guide
GV
Gas Valve Fault
The gas valve is not responding to commands from the PCB.
High
Engineer
View Guide
HT
DHW Overheat
The domestic hot water temperature has exceeded safe limits.
High
Engineer
View Guide
L0
Safety Limit Lockout (Generic)
A safety device has operated. This is a catch-all lockout code when a specific fault cannot…
High
Engineer
View Guide
L1
Flow Overheat / No Water Flow Lockout
The boiler has locked out because the flow temperature is too high or no water is…
High
Engineer
View Guide
L10
Overheat Lockout — Maximum Temperature Exceeded
The boiler has reached its absolute maximum temperature and locked out. A more severe overheat than…
High
Engineer
View Guide
L11
Central Heating Thermistor Fault
The central heating NTC thermistor is reading outside its normal range. The sensor may have developed…
Medium
Engineer
View Guide
L2
Ignition Lockout
The boiler has locked out after failing to ignite or losing its flame. A persistent version…
Medium
DIY
View Guide
L3
Fan Lockout
The boiler fan has failed to reach the required speed after multiple attempts.
High
Engineer
View Guide
L4
Overheat Lockout
The boiler's safety overheat thermostat has triggered a lockout due to excessively high temperatures.
High
Engineer
View Guide
L5
Too Many Resets
The boiler has been reset 5 times within 15 minutes and has entered a protective lockout.
Medium
DIY
View Guide
L6
False Flame Lockout
The boiler has detected an ionisation signal when the gas valve should be closed. This is…
High
Engineer
View Guide
L7
DHW Thermistor Lockout
The domestic hot water temperature sensor has caused a lockout — either due to a sensor…
High
Engineer
View Guide
L8
Flue Temperature Lockout
The flue gas temperature sensor has detected an unsafe temperature, causing a lockout.
High
Engineer
View Guide
L9
PCB Fault / Unconfigured
The PCB has an internal fault or has not been configured correctly. L9 is the lockout…
High
Engineer
View Guide
LC
Too Many Resets (5 Within 15 Minutes)
The boiler has been reset 5 or more times within 15 minutes and has entered a…
Medium
DIY
View Guide
LF
Low Gas Pressure Warning
The boiler has detected that the gas supply pressure is lower than expected, which may cause…
Medium
Engineer
View Guide
LN
Flame Loss Lockout (Alternative Code)
On some Ideal models, LN is a lockout version of FN/F2, indicating repeated flame loss requiring…
Medium
DIY
View Guide
SE
Sensor Error
One or more NTC temperature sensors are reading outside expected range.
Medium
Engineer
View Guide